Contents
The Massey Ferguson DTC (Diagnostic Trouble Code) Fault Codes List (from 10.X.27 to 4.02.E5) comprises a series of alphanumeric codes that serve as indicators of potential issues within the equipment’s electronic control system. These codes provide valuable diagnostic information to technicians, aiding in the identification and resolution of problems. Each code corresponds to a specific fault or malfunction within the equipment, allowing for more efficient troubleshooting and maintenance.
These fault codes cover a wide range of potential issues, including but not limited to engine performance, fuel system problems, transmission issues, hydraulic system malfunctions, and electrical faults. By referring to the DTC list and interpreting the codes displayed, technicians can quickly pinpoint the source of the problem and take appropriate action to rectify it.
Massey Ferguson Fault Codes List
Understanding and effectively utilizing the Massey Ferguson DTC Fault Codes List is essential for ensuring the proper functioning and reliability of Massey Ferguson equipment (Tractors: 4707, 4708, 4709, 4710, 5608, 5609, 5610, 5611, 5612, 5613; 5710SL, 5711SL, 5712SL, 5713SL, 7614, 7615, 7616, 7618, 7619, 7620, 7622, 7624, 7626, 7714, 7715, 7715S, 7716, 7718, 7719, 7720, 7722, 7724, 7726). It enables technicians to diagnose issues accurately, minimize downtime, and optimize equipment performance for maximum productivity.
MF Error Codes from 10.X.27 to 13.X.47
| MF Error Code | Massey Ferguson Error Code Description |
|---|---|
| 10.X.27 | Issue With Signal To Left Cab Fan Speed Controller (AIRCON) |
| 10.X.28 | Issue With Voltage To Air Conditioning Module (AIRCON) |
| 10.X.29 | Issue With Voltage To Air Conditioning Module (AIRCON) |
| 10.X.30 | Issue With Signal To Right Cab Fan Speed Controller (AIRCON) |
| 10.X.31 | Issue With Signal To Left Cab Fan Speed Controller (AIRCON) |
| 10.X.32 | Issue With Signal To Right Cab Fan Speed Controller (AIRCON) |
| 10.X.33 | Air Vent Circulation Flap Position Sensor Voltage Issue (AIRCON) |
| 13.00.04 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.05 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.06 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.07 | Air Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.08 | Air Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.09 | Air Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.0B | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.0C | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.0E | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.00.15 | Park Brake Release Solenoid Open Circuit Dyna VT (TRANS1) |
| 13.00.16 | Park Brake Release Solenoid High Amp Draw Dyna VT (TRANS1) |
| 13.00.17 | Park Brake Release Solenoid Low Amp Draw Dyna VT (TRANS1) |
| 13.00.18 | Brake System Pressure Not Dropped When Brake Applied Dyna VT (TRANS1) |
| 13.00.19 | Brake System Pressure Too High Dyna VT (TRANS1) |
| 13.00.1A | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.00.2D | Brake System Pressure Signal Issue Dyna VT (TRANS1) |
| 13.00.2E | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.00.2F | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.00.30 | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.00.38 | Issue With Emergency Steering Pressure Dyna VT (TRANS1) |
| 13.00.41 | Park Brake Released Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.00.42 | Park Brake Released Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.00.43 | Park Brake Activated Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.00.44 | Park Brake Activated Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.00.45 | Park Brake Activated Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.00.46 | Park Brake Released Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.00.47 | Park Brake Switch Not Closing When Park Brake Disengaged Dyna 6 (HITCH) |
| 13.00.48 | Park Brake Switch Not Opening When Park Brake Engaged Dyna 6 (HITCH) |
| 13.00.49 | Park Brake Wear Switch Not Opening Dyna 6 (HITCH) |
| 13.01.04 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.05 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.06 | Air Brake Park Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.07 | Air Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.08 | Air Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.09 | Air Brake Solenoid Issue Dyna 6 (TRANS1) |
| 13.01.0B | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.0C | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.0E | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.01.15 | Park Brake Release Solenoid Open Circuit Dyna VT (TRANS1) |
| 13.01.16 | Park Brake Release Solenoid High Amp Draw Dyna VT (TRANS1) |
| 13.01.17 | Park Brake Release Solenoid Low Amp Draw Dyna VT (TRANS1) |
| 13.01.18 | Brake System Pressure Not Dropped When Brake Applied Dyna VT (TRANS1) |
| 13.01.19 | Brake System Pressure Too High Dyna VT (TRANS1) |
| 13.01.1A | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.01.2D | Brake System Pressure Signal Issue Dyna VT (TRANS1) |
| 13.01.2E | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.01.2F | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.01.30 | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.01.38 | Issue With Emergency Steering Pressure Dyna VT (TRANS1) |
| 13.01.41 | Park Brake Released Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.01.42 | Park Brake Released Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.01.43 | Park Brake Activated Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.01.44 | Park Brake Activated Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.01.45 | Park Brake Activated Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.01.46 | Park Brake Released Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.01.47 | Park Brake Switch Not Closing When Park Brake Disengaged Dyna 6 (HITCH) |
| 13.01.48 | Park Brake Switch Not Opening When Park Brake Engaged Dyna 6 (HITCH) |
| 13.01.49 | Park Brake Wear Switch Not Opening Dyna 6 (HITCH) |
| 13.02.04 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.05 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.06 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.07 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.08 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.09 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.02.0B | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.02.0C | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.02.0E | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.02.15 | Park Brake Release Solenoid Open Circuit Dyna VT (TRANS1) |
| 13.02.16 | Park Brake Release Solenoid High Amp Draw Dyna VT (TRANS1) |
| 13.02.17 | Park Brake Release Solenoid Low Amp Draw Dyna VT (TRANS1) |
| 13.02.18 | Brake System Pressure Not Dropped When Brake Applied Dyna VT (TRANS1) |
| 13.02.19 | Brake System Pressure Too High Dyna VT (TRANS1) |
| 13.02.1A | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.02.2D | Brake System Pressure Signal Issue Dyna VT (TRANS1) |
| 13.02.2E | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.02.2F | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.02.30 | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.02.38 | Issue With Emergency Steering Pressure Dyna VT (TRANS1) |
| 13.02.41 | Park Brake Released Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.02.42 | Park Brake Released Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.02.43 | Park Brake Activated Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.02.44 | Park Brake Activated Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.02.45 | Park Brake Activated Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.02.46 | Park Brake Released Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.02.47 | Park Brake Switch Not Closing When Park Brake Disengaged Dyna 6 (HITCH) |
| 13.02.48 | Park Brake Switch Not Opening When Park Brake Engaged Dyna 6 (HITCH) |
| 13.02.49 | Park Brake Wear Switch Not Opening Dyna 6 (HITCH) |
| 13.03.04 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.05 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.06 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.07 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.08 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.09 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.03.0B | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.03.0C | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.03.0E | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.03.15 | Park Brake Release Solenoid Open Circuit Dyna VT (TRANS1) |
| 13.03.16 | Park Brake Release Solenoid High Amp Draw Dyna VT (TRANS1) |
| 13.03.17 | Park Brake Release Solenoid Low Amp Draw Dyna VT (TRANS1) |
| 13.03.18 | Brake System Pressure Not Dropped When Brake Applied Dyna VT (TRANS1) |
| 13.03.19 | Brake System Pressure Too High Dyna VT (TRANS1) |
| 13.03.1A | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.03.2D | Brake System Pressure Signal Issue Dyna VT (TRANS1) |
| 13.03.2E | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.03.2F | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.03.30 | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.03.38 | Issue With Emergency Steering Pressure Dyna VT (TRANS1) |
| 13.03.41 | Park Brake Released Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.03.42 | Park Brake Released Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.03.43 | Park Brake Activated Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.03.44 | Park Brake Activated Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.03.45 | Park Brake Activated Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.03.46 | Park Brake Released Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.03.47 | Park Brake Switch Not Closing When Park Brake Disengaged Dyna 6 (HITCH) |
| 13.03.48 | Park Brake Switch Not Opening When Park Brake Engaged Dyna 6 (HITCH) |
| 13.03.49 | Park Brake Wear Switch Not Opening Dyna 6 (HITCH) |
| 13.X.04 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.X.05 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.X.06 | Air Brake Park Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.X.07 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.X.08 | Air Brake Solenoid Issue Dyna VT / Dyna 6 (TRANS1) |
| 13.X.09 | Air Brake Solenoid Issue Dyna 6 / Dyna VT (TRANS1) |
| 13.X.0B | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.X.0C | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.X.0E | Hydraulic Trailer Brake Solenoid Issue Dyna VT (TRANS1) |
| 13.X.15 | Park Brake Release Solenoid Open Circuit Dyna VT (TRANS1) |
| 13.X.16 | Park Brake Release Solenoid High Amp Draw Dyna VT (TRANS1) |
| 13.X.17 | Park Brake Release Solenoid Low Amp Draw Dyna VT (TRANS1) |
| 13.X.18 | Brake System Pressure Not Dropped When Brake Applied Dyna VT (TRANS1) |
| 13.X.19 | Brake System Pressure Too High Dyna VT (TRANS1) |
| 13.X.1A | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.X.2D | Brake System Pressure Signal Issue Dyna VT (TRANS1) |
| 13.X.2E | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.X.2F | Issue With Park Lock Proximity Switch On The Axle Dyna VT (TRANS1) |
| 13.X.30 | Park Brake System Pressure Issue Dyna VT (TRANS1) |
| 13.X.38 | Issue With Emergency Steering Pressure Dyna VT (TRANS1) |
| 13.X.41 | Park Brake Released Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.X.42 | Park Brake Released Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.X.43 | Park Brake Activated Solenoid High Amp Draw Dyna 6 (HITCH) |
| 13.X.44 | Park Brake Activated Solenoid Low Amp Draw Dyna 6 (HITCH) |
| 13.X.45 | Park Brake Activated Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.X.46 | Park Brake Released Solenoid Voltage Issue Dyna 6 (HITCH) |
| 13.X.47 | Park Brake Switch Not Closing When Park Brake Disengaged Dyna 6 (HITCH) |
MF Error Codes from 13.X.48 to 3.01.9B
| MF Error Code | Massey Ferguson Error Code Description |
|---|---|
| 13.X.48 | Park Brake Switch Not Opening When Park Brake Engaged Dyna 6 (HITCH) |
| 13.X.49 | Park Brake Wear Switch Not Opening Dyna 6 (HITCH) |
| 14.00.01 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.00.02 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.00.03 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.00.04 | High Pressure Brake System Pressure DYNA 6 (TRANS1) |
| 14.00.05 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.00.06 | High Pressure Brake System Charging Too Often DYNA 6 (TRANS1) |
| 14.00.07 | Brake Pressure Sensor Open Circuit Dyna 6 (TRANS1) |
| 14.00.08 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.00.09 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.00.0A | Brake Pressure Sensor High Volts Dyna 6 (TRANS1) |
| 14.00.0B | High Pressure Brake System Pressure Not Dropping DYNA 6 (TRANS1) |
| 14.01.01 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.01.02 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.01.03 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.01.04 | High Pressure Brake System Pressure DYNA 6 (TRANS1) |
| 14.01.05 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.01.06 | High Pressure Brake System Charging Too Often DYNA 6 (TRANS1) |
| 14.01.07 | Brake Pressure Sensor Open Circuit Dyna 6 (TRANS1) |
| 14.01.08 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.01.09 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.01.0A | Brake Pressure Sensor High Volts Dyna 6 (TRANS1) |
| 14.01.0B | High Pressure Brake System Pressure Not Dropping DYNA 6 (TRANS1) |
| 14.02.01 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.02.02 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.02.03 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.02.04 | High Pressure Brake System Pressure DYNA 6 (TRANS1) |
| 14.02.05 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.02.06 | High Pressure Brake System Charging Too Often DYNA 6 (TRANS1) |
| 14.02.07 | Brake Pressure Sensor Open Circuit Dyna 6 (TRANS1) |
| 14.02.08 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.02.09 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.02.0A | Brake Pressure Sensor High Volts Dyna 6 (TRANS1) |
| 14.02.0B | High Pressure Brake System Pressure Not Dropping DYNA 6 (TRANS1) |
| 14.03.01 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.03.02 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.03.03 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.03.04 | High Pressure Brake System Pressure DYNA 6 (TRANS1) |
| 14.03.05 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.03.06 | High Pressure Brake System Charging Too Often DYNA 6 (TRANS1) |
| 14.03.07 | Brake Pressure Sensor Open Circuit Dyna 6 (TRANS1) |
| 14.03.08 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.03.09 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.03.0A | Brake Pressure Sensor High Volts Dyna 6 (TRANS1) |
| 14.03.0B | High Pressure Brake System Pressure Not Dropping DYNA 6 (TRANS1) |
| 14.X.01 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.X.02 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.X.03 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.X.04 | High Pressure Brake System Pressure DYNA 6 (TRANS1) |
| 14.X.05 | High Pressure Brake System Pressure Too High DYNA 6 (TRANS1) |
| 14.X.06 | High Pressure Brake System Charging Too Often DYNA 6 (TRANS1) |
| 14.X.07 | Brake Pressure Sensor Open Circuit Dyna 6 (TRANS1) |
| 14.X.08 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.X.09 | High Pressure Brake System Pressure Too Low DYNA 6 (TRANS1) |
| 14.X.0A | Brake Pressure Sensor High Volts Dyna 6 (TRANS1) |
| 14.X.0B | High Pressure Brake System Pressure Not Dropping DYNA 6 (TRANS1) |
| 1B.00.01 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.00.02 | Issue When Storing Configuration In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.00.03 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.00.04 | Issue With The LIN BUS Communication Between Linkage/PTO/Light Module On The B-Pillar And The B-Pillar Button Panel |
| 1B.00.05 | Internal Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.00.06 | CAN BUS Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.00.07 | Issue With Signal From Hitch Draft Control Dial |
| 1B.00.08 | Issue With Signal From Hitch Maximum Height Dial |
| 1B.00.09 | Issue With Signal From Hitch Drop Rate Control Dial |
| 1B.01.01 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.01.02 | Issue When Storing Configuration In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.01.03 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.01.04 | Issue With The LIN BUS Communication Between Linkage/PTO/Light Module On The B-Pillar And The B-Pillar Button Panel |
| 1B.01.05 | Internal Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.01.06 | CAN BUS Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.01.07 | Issue With Signal From Hitch Draft Control Dial |
| 1B.01.08 | Issue With Signal From Hitch Maximum Height Dial |
| 1B.01.09 | Issue With Signal From Hitch Drop Rate Control Dial |
| 1B.02.01 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.02.02 | Issue When Storing Configuration In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.02.03 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.02.04 | Issue With The LIN BUS Communication Between Linkage/PTO/Light Module On The B-Pillar And The B-Pillar Button Panel |
| 1B.02.05 | Internal Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.02.06 | CAN BUS Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.02.07 | Issue With Signal From Hitch Draft Control Dial |
| 1B.02.08 | Issue With Signal From Hitch Maximum Height Dial |
| 1B.02.09 | Issue With Signal From Hitch Drop Rate Control Dial |
| 1B.03.01 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.03.02 | Issue When Storing Configuration In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.03.03 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.03.04 | Issue With The LIN BUS Communication Between Linkage/PTO/Light Module On The B-Pillar And The B-Pillar Button Panel |
| 1B.03.05 | Internal Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.03.06 | CAN BUS Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.03.07 | Issue With Signal From Hitch Draft Control Dial |
| 1B.03.08 | Issue With Signal From Hitch Maximum Height Dial |
| 1B.03.09 | Issue With Signal From Hitch Drop Rate Control Dial |
| 1B.X.01 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.X.02 | Issue When Storing Configuration In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.X.03 | Issue With Configuration Stored In The Linkage/PTO/Light Module On The B-Pillar |
| 1B.X.04 | Issue With The LIN BUS Communication Between Linkage/PTO/Light Module On The B-Pillar And The B-Pillar Button Panel |
| 1B.X.05 | Internal Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.X.06 | CAN BUS Issue With The Linkage/PTO/Light Module On The B-Pillar |
| 1B.X.07 | Issue With Signal From Hitch Draft Control Dial |
| 1B.X.08 | Issue With Signal From Hitch Maximum Height Dial |
| 1B.X.09 | Issue With Signal From Hitch Drop Rate Control Dial |
| 3.00.19 | CAN Bus Message From Joystick Controls On Arm Rest (MFA) |
| 3.00.1A | CAN Bus Message From Spool Valve Controls 1 And 2 On Arm Rest (MFA) |
| 3.00.80 | Issue With 10 Volt Supply From TECU Module (TECU) |
| 3.00.81 | Issue With TECU Module (TECU) |
| 3.00.83 | Issue With TECU Module (TECU) |
| 3.00.84 | Issue With TECU Module (TECU) |
| 3.00.85 | Issue With TECU Module (TECU) |
| 3.00.86 | High Amp Draw On Auxiliary Valve Switch 3 (TECU) |
| 3.00.87 | High Voltage On Auxiliary Valve Switch 3 (TECU) / Calibration Issue For Valve Switch 3 (TECU) |
| 3.00.8A | High Amp Draw On Auxiliary Valve Switch 4 (TECU) |
| 3.00.8B | High Voltage On Auxiliary Valve Switch 4 (TECU) |
| 3.00.8C | Calibration Issue For Valve Switch 4 (TECU) |
| 3.00.94 | High Amp Draw On Auxiliary Valve Switch 6 (TECU) |
| 3.00.95 | High Voltage On Auxiliary Valve Switch 6 (TECU) |
| 3.00.96 | Calibration Issue For Valve Switch 6 (TECU) |
| 3.00.97 | High Amp Draw On Auxiliary Valve Switch 7 (TECU) |
| 3.00.98 | High Voltage On Auxiliary Valve Switch 7 (TECU) |
| 3.00.99 | Calibration Issue For Valve Switch 7 (TECU) |
| 3.00.9A | High Amp Draw On Auxiliary Valve Switch 8 (TECU) |
| 3.00.9B | High Voltage On Auxiliary Valve Switch 8 (TECU) |
| 3.00.9C | Calibration Issue For Valve Switch 8 (TECU) |
| 3.00.9D | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.00.9E | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.00.9F | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.00.A0 | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.00.A1 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.00.A2 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.00.A3 | Issue With TECU Module (TECU) |
| 3.01.19 | CAN Bus Message From Joystick Controls On Arm Rest (MFA) |
| 3.01.1A | CAN Bus Message From Spool Valve Controls 1 And 2 On Arm Rest (MFA) |
| 3.01.80 | Issue With 10 Volt Supply From TECU Module (TECU) |
| 3.01.81 | Issue With TECU Module (TECU) |
| 3.01.83 | Issue With TECU Module (TECU) |
| 3.01.84 | Issue With TECU Module (TECU) |
| 3.01.85 | Issue With TECU Module (TECU) |
| 3.01.86 | High Amp Draw On Auxiliary Valve Switch 3 (TECU) |
| 3.01.87 | High Voltage On Auxiliary Valve Switch 3 (TECU) / Calibration Issue For Valve Switch 3 (TECU) |
| 3.01.8A | High Amp Draw On Auxiliary Valve Switch 4 (TECU) |
| 3.01.8B | High Voltage On Auxiliary Valve Switch 4 (TECU) |
| 3.01.8C | Calibration Issue For Valve Switch 4 (TECU) |
| 3.01.94 | High Amp Draw On Auxiliary Valve Switch 6 (TECU) |
| 3.01.95 | High Voltage On Auxiliary Valve Switch 6 (TECU) |
| 3.01.96 | Calibration Issue For Valve Switch 6 (TECU) |
| 3.01.97 | High Amp Draw On Auxiliary Valve Switch 7 (TECU) |
| 3.01.98 | High Voltage On Auxiliary Valve Switch 7 (TECU) |
| 3.01.99 | Calibration Issue For Valve Switch 7 (TECU) |
| 3.01.9A | High Amp Draw On Auxiliary Valve Switch 8 (TECU) |
| 3.01.9B | High Voltage On Auxiliary Valve Switch 8 (TECU) |
MF Error Codes from 3.01.9C to 4.00.24
| MF Error Code | Massey Ferguson Error Code Description |
|---|---|
| 3.01.9C | Calibration Issue For Valve Switch 8 (TECU) |
| 3.01.9D | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.01.9E | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.01.9F | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.01.A0 | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.01.A1 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.01.A2 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.01.A3 | Issue With TECU Module (TECU) |
| 3.02.19 | CAN Bus Message From Joystick Controls On Arm Rest (MFA) |
| 3.02.1A | CAN Bus Message From Spool Valve Controls 1 And 2 On Arm Rest (MFA) |
| 3.02.80 | Issue With 10 Volt Supply From TECU Module (TECU) |
| 3.02.81 | Issue With TECU Module (TECU) |
| 3.02.83 | Issue With TECU Module (TECU) |
| 3.02.84 | Issue With TECU Module (TECU) |
| 3.02.85 | Issue With TECU Module (TECU) |
| 3.02.86 | High Amp Draw On Auxiliary Valve Switch 3 (TECU) |
| 3.02.87 | High Voltage On Auxiliary Valve Switch 3 (TECU) |
| 3.02.87 | High Voltage On Auxiliary Valve Switch 3 (TECU) |
| 3.02.8A | High Amp Draw On Auxiliary Valve Switch 4 (TECU) |
| 3.02.8B | High Voltage On Auxiliary Valve Switch 4 (TECU) |
| 3.02.8C | Calibration Issue For Valve Switch 4 (TECU) |
| 3.02.94 | High Amp Draw On Auxiliary Valve Switch 6 (TECU) |
| 3.02.95 | High Voltage On Auxiliary Valve Switch 6 (TECU) |
| 3.02.96 | Calibration Issue For Valve Switch 6 (TECU) |
| 3.02.97 | High Amp Draw On Auxiliary Valve Switch 7 (TECU) |
| 3.02.98 | High Voltage On Auxiliary Valve Switch 7 (TECU) |
| 3.02.99 | Calibration Issue For Valve Switch 7 (TECU) |
| 3.02.9A | High Amp Draw On Auxiliary Valve Switch 8 (TECU) |
| 3.02.9B | High Voltage On Auxiliary Valve Switch 8 (TECU) |
| 3.02.9C | Calibration Issue For Valve Switch 8 (TECU) |
| 3.02.9D | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.02.9E | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.02.9F | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.02.A0 | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.02.A1 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.02.A2 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.02.A3 | Issue With TECU Module (TECU) |
| 3.03.19 | CAN Bus Message From Joystick Controls On Arm Rest (MFA) |
| 3.03.1A | CAN Bus Message From Spool Valve Controls 1 And 2 On Arm Rest (MFA) |
| 3.03.80 | Issue With 10 Volt Supply From TECU Module (TECU) |
| 3.03.81 | Issue With TECU Module (TECU) |
| 3.03.83 | Issue With TECU Module (TECU) |
| 3.03.84 | Issue With TECU Module (TECU) |
| 3.03.85 | Issue With TECU Module (TECU) |
| 3.03.86 | High Amp Draw On Auxiliary Valve Switch 3 (TECU) |
| 3.03.87 | Calibration Issue For Valve Switch 3 (TECU) |
| 3.03.87 | Calibration Issue For Valve Switch 3 (TECU) |
| 3.03.8A | High Amp Draw On Auxiliary Valve Switch 4 (TECU) |
| 3.03.8B | High Voltage On Auxiliary Valve Switch 4 (TECU) |
| 3.03.8C | Calibration Issue For Valve Switch 4 (TECU) |
| 3.03.94 | High Amp Draw On Auxiliary Valve Switch 6 (TECU) |
| 3.03.95 | High Voltage On Auxiliary Valve Switch 6 (TECU) |
| 3.03.96 | Calibration Issue For Valve Switch 6 (TECU) |
| 3.03.97 | High Amp Draw On Auxiliary Valve Switch 7 (TECU) |
| 3.03.98 | High Voltage On Auxiliary Valve Switch 7 (TECU) |
| 3.03.99 | Calibration Issue For Valve Switch 7 (TECU) |
| 3.03.9A | High Amp Draw On Auxiliary Valve Switch 8 (TECU) |
| 3.03.9B | High Voltage On Auxiliary Valve Switch 8 (TECU) |
| 3.03.9C | Calibration Issue For Valve Switch 8 (TECU) |
| 3.03.9D | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.03.9E | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.03.9F | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.03.A0 | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.03.A1 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.03.A2 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.03.A3 | Issue With TECU Module (TECU) |
| 3.X.19 | CAN Bus Message From Joystick Controls On Arm Rest (MFA) |
| 3.X.1A | CAN Bus Message From Spool Valve Controls 1 And 2 On Arm Rest (MFA) |
| 3.X.80 | Issue With 10 Volt Supply From TECU Module (TECU) |
| 3.X.81 | Issue With TECU Module (TECU) |
| 3.X.83 | Issue With TECU Module (TECU) |
| 3.X.84 | Issue With TECU Module (TECU) |
| 3.X.85 | Issue With TECU Module (TECU) |
| 3.X.86 | High Amp Draw On Auxiliary Valve Switch 3 (TECU) |
| 3.X.87 | High Voltage On Auxiliary Valve Switch 3 (TECU) / Calibration Issue For Valve Switch 3 (TECU) |
| 3.X.8A | High Amp Draw On Auxiliary Valve Switch 4 (TECU) |
| 3.X.8B | High Voltage On Auxiliary Valve Switch 4 (TECU) |
| 3.X.8C | Calibration Issue For Valve Switch 4 (TECU) |
| 3.X.94 | High Amp Draw On Auxiliary Valve Switch 6 (TECU) |
| 3.X.95 | High Voltage On Auxiliary Valve Switch 6 (TECU) |
| 3.X.96 | Calibration Issue For Valve Switch 6 (TECU) |
| 3.X.97 | High Amp Draw On Auxiliary Valve Switch 7 (TECU) |
| 3.X.98 | High Voltage On Auxiliary Valve Switch 7 (TECU) |
| 3.X.99 | Calibration Issue For Valve Switch 7 (TECU) |
| 3.X.9A | High Amp Draw On Auxiliary Valve Switch 8 (TECU) |
| 3.X.9B | High Voltage On Auxiliary Valve Switch 8 (TECU) |
| 3.X.9C | Calibration Issue For Valve Switch 8 (TECU) |
| 3.X.9D | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.X.9E | Issue With Hand Throttle On Arm Rest Signal Voltage (MFA) |
| 3.X.9F | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.X.A0 | Issue With Hitch Depth Control Dial On Armrest Signal Voltage (MFA) |
| 3.X.A1 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.X.A2 | Issue With Speed Control Lever Position Sensor On Armrest Signal Voltage (MFA) |
| 3.X.A3 | Issue With TECU Module (TECU) |
| 4.0.03 | Issue With Clutch Pedal Safety Start Switch (TRANS) |
| 4.0.04 | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.0.09 | Forward Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.0A | Forward Clutch Solenoid Voltage Issue (TRANS) |
| 4.0.0B | Forward Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.0C | Forward Clutch Solenoid Open Circuit (TRANS) |
| 4.0.0D | Forward Clutch Solenoid Open Circuit (TRANS) |
| 4.0.0E | Forward Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.0F | Reverse Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.10 | Reverse Clutch Solenoid Voltage Issue (TRANS) |
| 4.0.11 | Reverse Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.12 | Reverse Clutch Solenoid Amp Draw Issue (TRANS) |
| 4.0.13 | Reverse Clutch Solenoid Open Circuit (TRANS) |
| 4.0.14 | Reverse Clutch Solenoid Low Amps (TRANS1) |
| 4.0.15 | Gear Lever Clutch Button Signal Received For Over 10 Seconds (TRANS) |
| 4.0.17 | Transmission Module Low Supply Voltage On 10 Volt Sensor Output Pin (TRANs) |
| 4.0.2C | Gear Lever Clutch Button Signal Received For Over 10 Seconds (TRANS) |
| 4.0.40 | Issue With Speed Sensor Values (TRANS) |
| 4.0.55 | Transmission Temperature Signal Out Of Range (TRANS) |
| 4.0.85 | Issue With Speed Sensor Values (TRANS) |
| 4.0.90 | Issue With Speed Sensor Values (TRANS) |
| 4.0.91 | Issue With Speed Sensor Values (TRANS) |
| 4.0.92 | Issue With Speed Sensor Values (TRANS) |
| 4.0.A2 | CAN BUS Message Missing (TRANS) |
| 4.0.A7 | Issue With Transmission Module (TRANS) |
| 4.0.C0 | Shuttle Lever Neutral Position Signal Error (TRANS) |
| 4.0.C1 | Shuttle Lever Neutral Position Signal Error (TRANS) |
| 4.0.C2 | Shuttle Lever Position Signal Error (TRANS) |
| 4.0.ED | Issue With Top Of Clutch Pedal Switch Or The operator Is Ridding The Clutch Pedal (TRANS) |
| 4.0.FD | Issue With Transmission Module (TRANS) |
| 4.0.FE | Issue With Transmission Module Calibrations Or Parameters (TRANS) |
| 4.0.FF | Issue With Transmission Module Calibrations Or Parameters (TRANS) |
| 4.00.04 | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.00.05 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.00.06 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.00.07 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.00.08 | Transmission High/Low Range Position Sensor Issue (TRANS) |
| 4.00.09 | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.0A | Forward Clutch Solenoid Voltage Issue (TRANS1) |
| 4.00.0B | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.0C | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.0D | Forward Clutch Solenoid Open Circuit (TRANS1) |
| 4.00.0E | Forward Clutch Solenoid Low Amps (TRANS1) |
| 4.00.0F | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.10 | Reverse Clutch Solenoid Voltage Issue (TRANS1) |
| 4.00.11 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.12 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.00.13 | Reverse Clutch Solenoid Open Circuit (TRANS1) |
| 4.00.14 | Reverse Clutch Solenoid Low Amps (TRANS1) |
| 4.00.15 | Transmission Pressure Switch Open When Engine Is Running (TRANS2) |
| 4.00.16 | Transmission Module Low Supply Voltage (TRANS) |
| 4.00.19 | Issue With The Stored Values For The Foot Throttle (TRANS) |
| 4.00.20 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.00.22 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.00.23 | Cruise Control Button Signal Issue (TRANS) |
| 4.00.24 | Park Lock Switch On Steering Column Direction Lever, Signal Issue (TRANS) |
MF Error Codes from 4.00.28 to 4.01.82
| Error Code | Massey Ferguson Error Code Description |
|---|---|
| 4.00.28 | Issue With Signal Voltage From Transmission Actuator (TRANS) |
| 4.00.29 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.00.2A | Transmission Output Speed Sensor Issue (TRANS) |
| 4.00.2B | Transmission Range Button Signal Issue (TRANS) |
| 4.00.2C | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.00.2D | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.00.2E | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.00.2F | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.00.31 | Transmission Hydrostatic Speed/Direction Sensor Issue (TRANS) |
| 4.00.33 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.00.40 | Issue With Speed Sensor Values (TRANS1) |
| 4.00.42 | Transmission Hydrostatic Speed/Direction Sensor Issue / Transmission Output Speed Sensor Issue (TRANS) |
| 4.00.44 | Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) |
| 4.00.46 | Pressure Is Not Seen To Drop When Turbo Clutch Solenoid Is Activated |
| 4.00.47 | Transmission Range Has Not Moved After Range Solenoid Has Been Energised (TRANS) |
| 4.00.48 | Transmission Range Has Not Moved To Neutral (TRANS) |
| 4.00.49 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.00.50 | Transmission Filter Blocked (TRANS) |
| 4.00.53 | Transmission Oil Temperature High |
| 4.00.54 | Transmission Temperature Signal Out Of Range (TRANS2) |
| 4.00.56 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.00.58 | Possible Transmission Slippage Detected |
| 4.00.59 | The Emergency Limp Mode Is Active |
| 4.00.61 | Issue With Low Speed Range Solenoid / Issue With Range 1 Solenoid Valve (TRANS1) |
| 4.00.62 | Issue With High Speed Range Solenoid / Issue With Range 2 Solenoid Valve (TRANS1) |
| 4.00.63 | Speed Limiting Valve Fault |
| 4.00.64 | Transmission Turbo Clutch Solenoid Voltage Supply Issue (TRANS) |
| 4.00.69 | Issue With Range 3 Solenoid Valve (TRANS1) |
| 4.00.6A | Issue With Range 4 Solenoid Valve (TRANS1) |
| 4.00.6B | Issue With Range 1 Engaged Switch Signal (TRANS1) |
| 4.00.6C | Issue With Range 2 Engaged Switch Signal (TRANS1) |
| 4.00.6D | Issue With Range 3 Engaged Switch Signal (TRANS1) |
| 4.00.6E | Issue With Range 4 Engaged Switch Signal (TRANS1) |
| 4.00.70 | Cruise Speed C1 Button Issue (TRANS) |
| 4.00.71 | Cruise Speed C2 Button Issue (TRANS) |
| 4.00.78 | Issue With Signal From Seat Switch (TRANS) |
| 4.00.82 | Transmission Speed Sensors Issue With Signals |
| 4.00.83 | Issue With One Of The Transmission Speed/Direction Sensors |
| 4.00.84 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.00.85 | Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) / Issue With Speed Sensor Values (TRANS1) |
| 4.00.86 | Transmission High Pressure Sensor Signal Voltage Issue (TRANS) |
| 4.00.89 | Transmission Oil Temperature Signal Issue (TRANS) |
| 4.00.8A | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.00.8F | Issue With Tyre Size Configuration (TRANS) |
| 4.00.90 | Issue With Speed Sensor Values (TRANS1) |
| 4.00.91 | Issue With Speed Sensor Values (TRANS1) |
| 4.00.92 | Issue With Speed Sensor Values (TRANS1) |
| 4.00.94 | CAN BUS Communication Issue Between Transmission And Arm Rest Module (TRANS) |
| 4.00.95 | Issue With Range 1 Engaged Switch And Range Solenoid 1 (TRANS1) |
| 4.00.96 | Issue With Range 2 Engaged Switch And Range Solenoid 2 (TRANS1) |
| 4.00.97 | Issue With Range 3 Engaged Switch And Range Solenoid 3 (TRANS1) |
| 4.00.98 | Issue With Range 4 Engaged Switch And Range Solenoid 4 (TRANS1) |
| 4.00.99 | Issue With Powershift P Solenoid Supply Voltage (TRANS2) |
| 4.00.9A | Issue With Powershift L Solenoid Supply Voltage (TRANS2) |
| 4.00.9B | Issue With Powershift N Solenoid Supply Voltage (TRANS2) |
| 4.00.9C | Transmission Input Shaft Speed Sensor Open Circuit (TRANS2) |
| 4.00.9D | Transmission Input Shaft Speed Sensor Calibration Fault (TRANS2) |
| 4.00.9E | Transmission Input Shaft Speed Sensor Signal Fault (TRANS2) |
| 4.00.A1 | Issue With Transmission Actuator (TRANS) |
| 4.00.A2 | Issue With Transmission Actuator (TRANS) |
| 4.00.A3 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.00.A4 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.00.A5 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.00.A6 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.00.B0 | Issue With Transmission Actuator Communication On CAN BUS (TRANS) |
| 4.00.B1 | Transmission Range Change Issue (TRANS) |
| 4.00.B2 | Transmission Internal Software Issue (TRANS) |
| 4.00.B5 | Transmission Internal Software Issue (TRANS) |
| 4.00.B8 | Issue With Intermediate Speed Sensor Values (TRANS1) |
| 4.00.E1 | Transmission Internal Software Issue (TRANS) |
| 4.00.E2 | Transmission Internal Software Issue (TRANS) |
| 4.00.E3 | Transmission Internal Software Issue (TRANS) |
| 4.00.E4 | Transmission Internal Software Issue (TRANS) |
| 4.00.E5 | Transmission Internal Software Issue (TRANS) |
| 4.00.E6 | Transmission Internal Software Issue (TRANS) |
| 4.00.E7 | Transmission Internal Software Issue (TRANS) |
| 4.00.E9 | Transmission Internal Software Issue (TRANS) |
| 4.00.EA | Transmission Internal Software Issue (TRANS) |
| 4.00.EB | Transmission Internal Software Issue (TRANS) |
| 4.00.EC | Drive Pedal Not Calibrated (TRANS) |
| 4.00.ED | Clutch Pedal Not Calibrated (TRANS) |
| 4.00.EE | Transmission Calibration Issue (TRANS) |
| 4.00.EF | Transmission Turbo Clutch Calibration Issue (TRANS) |
| 4.00.F0 | Transmission Calibration Issue (TRANS) |
| 4.00.F1 | Transmission Calibration Issue (TRANS) |
| 4.00.F2 | Transmission Calibration Issue (TRANS) |
| 4.00.F3 | Transmission Calibration Issue (TRANS) |
| 4.00.FF | Internal Issue With Transmission Module (TRANS) |
| 4.00.FF | Internal Issue With Transmission Module (TRANS) |
| 4.01.04 | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.01.05 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.01.06 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.01.07 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.01.08 | Transmission High/Low Range Position Sensor Issue (TRANS) |
| 4.01.09 | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.0A | Forward Clutch Solenoid Voltage Issue (TRANS1) |
| 4.01.0B | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.0C | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.0D | Forward Clutch Solenoid Open Circuit (TRANS1) |
| 4.01.0E | Forward Clutch Solenoid Low Amps (TRANS1) |
| 4.01.0F | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.10 | Reverse Clutch Solenoid Voltage Issue (TRANS1) |
| 4.01.11 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.12 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.01.13 | Reverse Clutch Solenoid Open Circuit (TRANS1) |
| 4.01.14 | Reverse Clutch Solenoid Low Amps (TRANS1) |
| 4.01.15 | Transmission Pressure Switch Open When Engine Is Running (TRANS2) |
| 4.01.16 | Transmission Module Low Supply Voltage (TRANS) |
| 4.01.19 | Issue With The Stored Values For The Foot Throttle (TRANS) |
| 4.01.20 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.01.22 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.01.23 | Cruise Control Button Signal Issue (TRANS) |
| 4.01.24 | Park Lock Switch On Steering Column Direction Lever, Signal Issue (TRANS) |
| 4.01.28 | Issue With Signal Voltage From Transmission Actuator (TRANS) |
| 4.01.29 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.01.2A | Transmission Output Speed Sensor Issue (TRANS) |
| 4.01.2B | Transmission Range Button Signal Issue (TRANS) |
| 4.01.2C | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.01.2D | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.01.2E | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.01.2F | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.01.31 | Transmission Hydrostatic Speed/Direction Sensor Issue (TRANS) |
| 4.01.33 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.01.40 | Issue With Speed Sensor Values (TRANS1) |
| 4.01.42 | Transmission Hydrostatic Speed/Direction Sensor Issue / Transmission Output Speed Sensor Issue (TRANS) |
| 4.01.44 | Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) |
| 4.01.46 | Pressure Is Not Seen To Drop When Turbo Clutch Solenoid Is Activated |
| 4.01.47 | Transmission Range Has Not Moved After Range Solenoid Has Been Energised (TRANS) |
| 4.01.48 | Transmission Range Has Not Moved To Neutral (TRANS) |
| 4.01.49 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.01.50 | Transmission Filter Blocked (TRANS) |
| 4.01.53 | Transmission Oil Temperature High |
| 4.01.54 | Transmission Temperature Signal Out Of Range (TRANS2) |
| 4.01.56 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.01.58 | Possible Transmission Slippage Detected |
| 4.01.59 | The Emergency Limp Mode Is Active |
| 4.01.61 | Issue With Low Speed Range Solenoid / Issue With Range 1 Solenoid Valve (TRANS1) |
| 4.01.62 | Issue With High Speed Range Solenoid / Issue With Range 2 Solenoid Valve (TRANS1) |
| 4.01.63 | Speed Limiting Valve Fault |
| 4.01.64 | Transmission Turbo Clutch Solenoid Voltage Supply Issue (TRANS) |
| 4.01.69 | Issue With Range 3 Solenoid Valve (TRANS1) |
| 4.01.6A | Issue With Range 4 Solenoid Valve (TRANS1) |
| 4.01.6B | Issue With Range 1 Engaged Switch Signal (TRANS1) |
| 4.01.6C | Issue With Range 2 Engaged Switch Signal (TRANS1) |
| 4.01.6D | Issue With Range 3 Engaged Switch Signal (TRANS1) |
| 4.01.6E | Issue With Range 4 Engaged Switch Signal (TRANS1) |
| 4.01.70 | Cruise Speed C1 Button Issue (TRANS) |
| 4.01.71 | Cruise Speed C2 Button Issue (TRANS) |
| 4.01.78 | Issue With Signal From Seat Switch (TRANS) |
| 4.01.82 | Transmission Speed Sensors Issue With Signals |
MF Error Codes from 4.01.83 to 4.02.E5
| Error Code | Massey Ferguson Error Code Description |
|---|---|
| 4.01.83 | Issue With One Of The Transmission Speed/Direction Sensors |
| 4.01.84 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.01.85 | Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) / Issue With Speed Sensor Values (TRANS1) |
| 4.01.86 | Transmission High Pressure Sensor Signal Voltage Issue (TRANS) |
| 4.01.89 | Transmission Oil Temperature Signal Issue (TRANS) |
| 4.01.8A | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.01.8F | Issue With Tyre Size Configuration (TRANS) |
| 4.01.90 | Issue With Speed Sensor Values (TRANS1) |
| 4.01.91 | Issue With Speed Sensor Values (TRANS1) |
| 4.01.92 | Issue With Speed Sensor Values (TRANS1) |
| 4.01.94 | CAN BUS Communication Issue Between Transmission And Arm Rest Module (TRANS) |
| 4.01.95 | Issue With Range 1 Engaged Switch And Range Solenoid 1 (TRANS1) |
| 4.01.96 | Issue With Range 2 Engaged Switch And Range Solenoid 2 (TRANS1) |
| 4.01.97 | Issue With Range 3 Engaged Switch And Range Solenoid 3 (TRANS1) |
| 4.01.98 | Issue With Range 4 Engaged Switch And Range Solenoid 4 (TRANS1) |
| 4.01.99 | Issue With Powershift P Solenoid Supply Voltage (TRANS2) |
| 4.01.9A | Issue With Powershift L Solenoid Supply Voltage (TRANS2) |
| 4.01.9B | Issue With Powershift N Solenoid Supply Voltage (TRANS2) |
| 4.01.9C | Transmission Input Shaft Speed Sensor Open Circuit (TRANS2) |
| 4.01.9D | Transmission Input Shaft Speed Sensor Calibration Fault (TRANS2) |
| 4.01.9E | Transmission Input Shaft Speed Sensor Signal Fault (TRANS2) |
| 4.01.A1 | Issue With Transmission Actuator (TRANS) |
| 4.01.A2 | Issue With Transmission Actuator (TRANS) |
| 4.01.A3 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.01.A4 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.01.A5 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.01.A6 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.01.B0 | Issue With Transmission Actuator Communication On CAN BUS (TRANS) |
| 4.01.B1 | Transmission Range Change Issue (TRANS) |
| 4.01.B2 | Transmission Internal Software Issue (TRANS) |
| 4.01.B5 | Transmission Internal Software Issue (TRANS) |
| 4.01.B8 | Issue With Intermediate Speed Sensor Values (TRANS1) |
| 4.01.E1 | Transmission Internal Software Issue (TRANS) |
| 4.01.E2 | Transmission Internal Software Issue (TRANS) |
| 4.01.E3 | Transmission Internal Software Issue (TRANS) |
| 4.01.E4 | Transmission Internal Software Issue (TRANS) |
| 4.01.E5 | Transmission Internal Software Issue (TRANS) |
| 4.01.E6 | Transmission Internal Software Issue (TRANS) |
| 4.01.E7 | Transmission Internal Software Issue (TRANS) |
| 4.01.E9 | Transmission Internal Software Issue (TRANS) |
| 4.01.EA | Transmission Internal Software Issue (TRANS) |
| 4.01.EB | Transmission Internal Software Issue (TRANS) |
| 4.01.EC | Drive Pedal Not Calibrated (TRANS) |
| 4.01.ED | Clutch Pedal Not Calibrated (TRANS) |
| 4.01.EE | Transmission Calibration Issue (TRANS) |
| 4.01.EF | Transmission Turbo Clutch Calibration Issue (TRANS) |
| 4.01.F0 | Transmission Calibration Issue (TRANS) |
| 4.01.F1 | Transmission Calibration Issue (TRANS) |
| 4.01.F2 | Transmission Calibration Issue (TRANS) |
| 4.01.F3 | Transmission Calibration Issue (TRANS) |
| 4.01.FF | Internal Issue With Transmission Module (TRANS) |
| 4.02.04 | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.02.04 | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.02.05 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.02.06 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.02.07 | Transmission High Pressure Sensor 2 Signal Voltage Issue (TRANS) |
| 4.02.08 | Transmission High/Low Range Position Sensor Issue (TRANS) |
| 4.02.09 | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.0A | Forward Clutch Solenoid Voltage Issue (TRANS1) |
| 4.02.0B | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.0C | Forward Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.0D | Forward Clutch Solenoid Open Circuit (TRANS1) |
| 4.02.0E | Forward Clutch Solenoid Low Amps (TRANS1) |
| 4.02.0F | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.10 | Reverse Clutch Solenoid Voltage Issue (TRANS1) |
| 4.02.11 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.12 | Reverse Clutch Solenoid Amp Draw Issue (TRANS1) |
| 4.02.13 | Reverse Clutch Solenoid Open Circuit (TRANS1) |
| 4.02.14 | Reverse Clutch Solenoid Low Amps (TRANS1) |
| 4.02.15 | Transmission Pressure Switch Open When Engine Is Running (TRANS2) |
| 4.02.16 | Transmission Module Low Supply Voltage (TRANS) |
| 4.02.19 | Issue With The Stored Values For The Foot Throttle (TRANS) |
| 4.02.20 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.02.22 | Issue With Signal Voltage From Foot Throttle Sensor (TRANS) |
| 4.02.23 | Cruise Control Button Signal Issue (TRANS) |
| 4.02.24 | Park Lock Switch On Steering Column Direction Lever, Signal Issue (TRANS) |
| 4.02.28 | Issue With Signal Voltage From Transmission Actuator (TRANS) |
| 4.02.29 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.02.2A | Transmission Output Speed Sensor Issue (TRANS) |
| 4.02.2B | Transmission Range Button Signal Issue (TRANS) |
| 4.02.2C | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.02.2D | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.02.2E | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.02.2F | Steering Column Forward/Reverse Drive Lever Issue (TRANS) |
| 4.02.31 | Transmission Hydrostatic Speed/Direction Sensor Issue (TRANS) |
| 4.02.33 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.02.40 | Issue With Speed Sensor Values (TRANS1) |
| 4.02.42 | Transmission Hydrostatic Speed/Direction Sensor Issue (TRANS) / Transmission Output Speed Sensor Issue (TRANS) |
| 4.02.44 | Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) |
| 4.02.46 | Pressure Is Not Seen To Drop When Turbo Clutch Solenoid Is Activated |
| 4.02.47 | Transmission Range Has Not Moved After Range Solenoid Has Been Energised (TRANS) |
| 4.02.48 | Transmission Range Has Not Moved To Neutral (TRANS) |
| 4.02.49 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.02.50 | Transmission Filter Blocked (TRANS) |
| 4.02.53 | Transmission Oil Temperature High |
| 4.02.54 | Transmission Temperature Signal Out Of Range (TRANS2) |
| 4.02.56 | Transmission Filter Blockage Sensor Issue (TRANS) |
| 4.02.58 | Possible Transmission Slippage Detected |
| 4.02.59 | The Emergency Limp Mode Is Active |
| 4.02.61 | Issue With Low Speed Range Solenoid / Issue With Range 1 Solenoid Valve (TRANS1) |
| 4.02.62 | Issue With High Speed Range Solenoid / Issue With Range 2 Solenoid Valve (TRANS1) |
| 4.02.63 | Speed Limiting Valve Fault |
| 4.02.64 | Transmission Turbo Clutch Solenoid Voltage Supply Issue (TRANS) |
| 4.02.69 | Issue With Range 3 Solenoid Valve (TRANS1) |
| 4.02.6A | Issue With Range 4 Solenoid Valve (TRANS1) |
| 4.02.6B | Issue With Range 1 Engaged Switch Signal (TRANS1) |
| 4.02.6C | Issue With Range 2 Engaged Switch Signal (TRANS1) |
| 4.02.6D | Issue With Range 3 Engaged Switch Signal (TRANS1) |
| 4.02.6E | Issue With Range 4 Engaged Switch Signal (TRANS1) |
| 4.02.70 | Cruise Speed C1 Button Issue (TRANS) |
| 4.02.71 | Cruise Speed C2 Button Issue (TRANS) |
| 4.02.78 | Issue With Signal From Seat Switch (TRANS) |
| 4.02.82 | Transmission Speed Sensors Issue With Signals |
| 4.02.83 | Issue With One Of The Transmission Speed/Direction Sensors |
| 4.02.84 | Issue With Message From Speed Lever On Armrest (TRANS) |
| 4.02.85 | Issue With Speed Sensor Values (TRANS1) / Issue With Signal From Transmission Mounted Engine Speed Sensor (TRANS) |
| 4.02.86 | Transmission High Pressure Sensor Signal Voltage Issue (TRANS) |
| 4.02.89 | Transmission Oil Temperature Signal Issue (TRANS) |
| 4.02.8A | Issue With Signal Voltage From Clutch Pedal Sensor (TRANS) |
| 4.02.8F | Issue With Tyre Size Configuration (TRANS) |
| 4.02.90 | Issue With Speed Sensor Values (TRANS1) |
| 4.02.91 | Issue With Speed Sensor Values (TRANS1) |
| 4.02.92 | Issue With Speed Sensor Values (TRANS1) |
| 4.02.94 | CAN BUS Communication Issue Between Transmission And Arm Rest Module (TRANS) |
| 4.02.95 | Issue With Range 1 Engaged Switch And Range Solenoid 1 (TRANS1) |
| 4.02.96 | Issue With Range 2 Engaged Switch And Range Solenoid 2 (TRANS1) |
| 4.02.97 | Issue With Range 3 Engaged Switch And Range Solenoid 3 (TRANS1) |
| 4.02.98 | Issue With Range 4 Engaged Switch And Range Solenoid 4 (TRANS1) |
| 4.02.99 | Issue With Powershift P Solenoid Supply Voltage (TRANS2) |
| 4.02.9A | Issue With Powershift L Solenoid Supply Voltage (TRANS2) |
| 4.02.9B | Issue With Powershift N Solenoid Supply Voltage (TRANS2) |
| 4.02.9C | Transmission Input Shaft Speed Sensor Open Circuit (TRANS2) |
| 4.02.9D | Transmission Input Shaft Speed Sensor Calibration Fault (TRANS2) |
| 4.02.9E | Transmission Input Shaft Speed Sensor Signal Fault (TRANS2) |
| 4.02.A1 | Issue With Transmission Actuator (TRANS) |
| 4.02.A2 | Issue With Transmission Actuator (TRANS) |
| 4.02.A3 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.02.A4 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.02.A5 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.02.A6 | Issue With Transmission Actuator Internal Position Sensor (TRANS) |
| 4.02.B0 | Issue With Transmission Actuator Communication On CAN BUS (TRANS) |
| 4.02.B1 | Transmission Range Change Issue (TRANS) |
| 4.02.B2 | Transmission Internal Software Issue (TRANS) |
| 4.02.B5 | Transmission Internal Software Issue (TRANS) |
| 4.02.B8 | Issue With Intermediate Speed Sensor Values (TRANS1) |
| 4.02.E1 | Transmission Internal Software Issue (TRANS) |
| 4.02.E2 | Transmission Internal Software Issue (TRANS) |
| 4.02.E3 | Transmission Internal Software Issue (TRANS) |
| 4.02.E4 | Transmission Internal Software Issue (TRANS) |
| 4.02.E5 | Transmission Internal Software Issue (TRANS) |
How to Сlear Massey Ferguson Fault Codes?
Clearing Massey Ferguson fault codes typically involves accessing the equipment’s diagnostic system and using specialized tools or procedures to reset the codes. Here’s a general guide on how to clear fault codes on Massey Ferguson equipment:
- Access the Diagnostic Interface: Depending on the specific model and type of equipment, you may need to access the diagnostic interface using a handheld diagnostic tool or through the equipment’s control panel.
- Enter Diagnostic Mode: Follow the manufacturer’s instructions to enter the diagnostic mode on the equipment. This may involve pressing specific buttons or following a sequence of steps to access the diagnostic menu.
- View Fault Codes: Once in the diagnostic mode, you can view the list of stored fault codes. Take note of the codes that you want to clear.
- Clear Fault Codes: Use the diagnostic tool or interface to clear the fault codes from the equipment’s memory. This process may vary depending on the specific diagnostic tool or equipment model.
- Verify Clearing: After clearing the fault codes, verify that the codes have been successfully removed from the system. Check the diagnostic menu again to ensure that no fault codes are present.
- Test Equipment: Once the fault codes have been cleared, test the equipment to ensure that the issue has been resolved. Monitor the equipment for any signs of recurring faults or abnormalities.
- Record Maintenance: Keep a record of the cleared fault codes and any actions taken to address the underlying issues. This information can be useful for future diagnostics and maintenance.
It’s important to note that clearing fault codes may only temporarily address the symptoms of an underlying issue. If the problem persists or recurs frequently, it’s recommended to perform a thorough diagnostic inspection and address any underlying issues to prevent further issues or damage to the equipment. Additionally, always refer to the equipment’s user manual or consult with a qualified technician for specific instructions on clearing fault codes for your Massey Ferguson equipment.
