Contents
Bulldozer
| Ground Clearance | 49.8 in (1264.92 mm) |
| Blade Capacity – Sae J1265* | 16.11 yd3 (12.31 m3) |
| Digging Depth | 25.4 in (645.16 mm) |
| Height | 4.41 ft in (1.35 m) |
| Maximum Tilt | 30.9 in (784.86 mm) |
| Note (1) | *Capacities calculated with a trash rack installed. |
| Note (2) | **Weight includes cylinder mounting, lift cylinder and lines, blade, push arms, trunnions, and cylinder lines (Tilt). |
| Weight** | 8492 lb (3851.91 kg) |
| Blade | 7S LGP |
| Width – Over End Bits | 14.91 ft in (4.55 m) |
Engine Details
| Displacement | 567 cu in (9.3 L) |
| Bore | 4.5 in (114.3 mm) |
| Stroke | 5.9 in (149.9 mm) |
| Net Power – Iso 9249 | 235 hp (175.3 kw) |
| Net Power – Sae J1349 | 235 hp (175.3 kw) |
| Gross Power – Sae J1995 | 259 hp (193.2 kw) |
| Engine Model | Cat C9.3 ACERT |
| Flywheel Power | 235 hp (175.3 kw) |
| Gross Power – Iso 14396 | 256 hp (190.9 kw) |
| Net Power – Iso 9249 (Din) | 238 hp (177.5 kw) |
| Global Emissions | US EPA Tier 4 Interim/EU Stage IIIB/Japan MLIT Step 4 |
| Gross Power – Iso 14396 (Din) | 260 hp (193.9 kw) |
Drive Train
| Drive Train Type | Electric Drive |
| Ac Compressor Nominal Input Voltage | 320 V |
| Ac Compressor Maximum Input Current | 12 A |
| Electric Water Pump System Nominal Input Voltage | 320 V |
| Electric Water Pump System Nominal Input Current | 5 A |
| Ac Generator And Propulsion Module Voltage | 480 V |
Operational Specs
| Operating Weight | 68600 lb (31116.5 kg) |
Weights
| Operating Weight – Lgp Wha | 68600 lb (31116.5 kg) |
| Shipping Weight – Lgp Wha | 58900 lb (26716.6 kg) |
Service Refill Capacities
| Cooling System | 22.5 gal (85.2 L) |
| Fuel Tank Capacity | 108 gal (408.9 L) |
| Engine Crankcase | 8 gal (30.3 L) |
| Power Train | 16 gal (60.6 L) |
| Pivot Shaft Compartment | 1.8 gal (6.9 L) |
| Final Drive – Each – Lgp | 9 gal (34.1 L) |
Standards
| Brakes | ISO 10265 2008 |
| ROPS/FOPS | ROPS meets criteria ISO 3471:1994, 2008; FOPS meets ISO 3449:1992, 2005 Level II |
| Cab | ANSI/SAE J1166 OCT 98 |
Hydraulic Controls – Main Relief Valve
| Pressure Setting – Steering | 4000 psi |
Hydraulic Controls – Maximum Operating Pressure
| Bulldozer | 4000 psi |
| Tilt Cylinder | 4000 psi |
| Ripper – Pitch | 4000 psi |
| Ripper – Lift | 4000 psi |
| Steering | 5950 psi |
Hydraulic Controls – Pump
| Lift Cylinder Flow | 42 gal/min |
| Ripper Cylinder Flow | 42 gal/min |
| Pump Output – Steering | 82.4 gal/min |
| Pump Output – Implement | 52.8 gal/min |
| Pump Type | Piston, Variable Displacement |
| Tilt Cylinder Flow – Head End Flow | 24.6 gal/min |
| Tilt Cylinder Flow – Rod End Flow | 17.4 gal/min |
Rippers
| Maximum Penetration Force | 19639 lb (8908.2 kg) |
| Pry-Out Force | 52695 lb (23902.1 kg) |
| Overall Beam Width | 82.2 in (2087.9 mm) |
| Beam Cross Section | 14 in (355.6 mm) |
| Weight – With One Shank | 3572 lb (1620.3 kg) |
| Weight – Each Additional Shank | 330 lb (149.7 kg) |
| Ramp Angle | 26 degrees |
| Pocket Spacing | 35.4 in (899.2 mm) |
| Shank Gauge | 70.9 in (1800.9 mm) |
| Shank Section | 72 mm 228 mm (2.8 in 9.0 in) |
| Rippers Type | Multi-Shank |
| Number Of Pockets | 3 |
| Maximum Clearance Raised – Under Tip, Pinned In Bottom Hole | 23.1 in (586.8 mm) |
| Maximum Penetration | 25.6 in (650.3 mm) |
Winches
| Weight* | 3350 lb (1519.6 kg) |
| Drum Capacity – 24 Mm (1 In) | 203 ft in (61.9 m) |
| Drum Capacity – 29 Mm (1.13 In) | 185 ft in (56.4 m) |
| Oil Capacity | 3.2 gal (12.2 L) |
| Winch Model | PA90 |
| Increased Tractor Length – Lgp | 93.9 in (2385.1 mm) |
| Drum Diameter | 12.5 in (317.5 mm) |
| Winch Drive | Hydraulic |
| Maximum Bare Drum – Line Pull | 90000 lb (40823.4 kg) |
| Maximum Full Drum – Line Pull | 57000 lb (25854.8 kg) |
| Maximum Bare Drum – Line Speed | 70 ft/min |
| Maximum Full Drum – Line Speed | 116 ft/min |
| Note | *Basic winch weight, mounting arrangement, hydraulic and electrical system weight. |
